Florida Concealed Carry banner
421 - 440 of 455 Posts

·
Registered
Joined
·
15,352 Posts
Discussion Starter · #421 ·
Some fun with photography and photoshop:
Air gun Trigger Gun barrel Gun accessory Electric blue


Air gun Trigger Gun barrel Gun accessory Metal


Trigger Font Rectangle Gun barrel Red
 

·
Registered
Joined
·
15,352 Posts
Discussion Starter · #422 ·
Finally launched the "Gold Dazzle" project today!
Pre-build mock-up:
Air gun Trigger Gun barrel Camouflage Gun accessory

Some of the themed parts:
Product Wood Rectangle Font Technology
Communication Device Font Material property Gadget Metal


Today I drilled the holes, tried in the (gold) pins, and removed the rail tabs:
Air gun Sleeve Trigger Gun barrel Shotgun

Brown Sleeve Font Eyewear Personal protective equipment

Top view of tab removal. The frame is gray, which is why you see that color under the cerakote paint job.
I still have to remove the recoil spring channel tab.
Rectangle Sleeve Wood Tints and shades Snow

Building Window Automotive tire Rectangle Asphalt

This going to be a nice one, I think!
 

·
Registered
Joined
·
15,352 Posts
Discussion Starter · #423 ·
Close-up of rail tabs:
Product Automotive tire Rectangle Bumper Automotive exterior


Got some flash to clean up on the pin holes.
 
  • Like
Reactions: BeerHunter

·
Registered
Joined
·
15,352 Posts
Discussion Starter · #424 ·
Tried in the Rook rails. Had to do a bit of smithing on one of the rear rails to get rid of a small "shiny crescent." After that, it all went together. Tried the slide on (without the barrel, since the channel tab is still there). Like buttah! Took a quick pic, too.
Trigger Gun barrel Wood Gun accessory Air gun
 
  • Like
Reactions: BeerHunter

·
Registered
Joined
·
15,352 Posts
Discussion Starter · #425 ·
premature post... working on project.
 

·
Registered
Joined
·
15,352 Posts
Discussion Starter · #427 ·
Nice!


Sent from my iPhone using Tapatalk
Think I'm going to find some time to work on it tomorrow. Should be able to get it finished or close to finished.
 

·
Super Moderator
Joined
·
31,675 Posts
Think I'm going to find some time to work on it tomorrow. Should be able to get it finished or close to finished.
So 15 minute the other day and another 15 min tomorrow to finish? 🤣🤣🤣
 
  • Haha
Reactions: racer88

·
Registered
Joined
·
15,352 Posts
Discussion Starter · #429 ·
  • Haha
Reactions: BeerHunter

·
Registered
Joined
·
15,352 Posts
Discussion Starter · #430 ·
Internet service was down for several hours, so I went to work at the Freedom Bench to get this Independence Day party started right! Build a gun! Well.. continue building it! The only thing left to do on the frame was to remove the Recoil Spring Assembly channel block and polish.

The Freedom Bench!
Automotive design Motor vehicle Gas Automotive exterior Machine


Hand Water Gesture Finger Automotive tire


Wood Material property Bumper Motor vehicle Gas


Finger Nail Wrist Thumb Cable


Finger Automotive tire Material property Gas Electric blue


Automotive tire Font Freezing Engineering Wood


Rectangle Electric blue Automotive tire Engineering Toy


Trigger Air gun Rectangle Gun barrel Gun accessory


Air gun Trigger Eyewear Gun barrel Shotgun
 
  • Like
Reactions: BeerHunter

·
Super Moderator
Joined
·
31,675 Posts
Looking good! (y)(y)
 
  • Like
Reactions: racer88

·
Registered
Joined
·
15,352 Posts
Discussion Starter · #432 ·
Looking good! (y)(y)
This is my 3rd build, and I'm still going WAY over the claimed (by politicians) 30 - 60 minutes to "slap it together like Legos!"

I probably spent 2 - 3 hours on just the channel block removal and polish.
 
  • Like
Reactions: BeerHunter

·
Super Moderator
Joined
·
31,675 Posts
This is my 3rd build, and I'm still going WAY over the claimed 30 - 60 minutes to "slap it together like Legos!"

I probably spent 2 - 3 hours on just the channel block removal and polish.
Proving Biden a liar once again, one "Ghost Gun" at a time! 🤣
 
  • Haha
Reactions: racer88

·
Registered
Joined
·
1,993 Posts
I just did the math. I have 3 extra Glock “uppers” and two P80s, looks line I need another “lower”.
 
  • Like
Reactions: Caleb and racer88

·
Registered
Joined
·
15,352 Posts
Discussion Starter · #436 ·
I just did the math. I have 3 extra Glock “uppers” and two P80s, looks line I need another “lower”.
Which kind of uppers? 17? 19? 26?
 

·
Registered
Joined
·
15,352 Posts
Discussion Starter · #437 · (Edited)
OK... here she is! Gold Dazzle? Golden Gun? Sights are on the way. Should have them sometime next week.

Slide is sticking a bit in the rearward position. So, I've got to sort that out. Once I've got all the functions working properly, I'll do safety testing.
Sleeve Gesture Collar Material property Font

Camouflage Sleeve Air gun Gesture Helmet

Bottle Drinkware Sleeve Yellow Art
 

·
Registered
Joined
·
8,321 Posts
  • Like
Reactions: racer88

·
Registered
Joined
·
15,352 Posts
Discussion Starter · #440 ·
A few more views. Can't wait to get the sights!
Rectangle Building Yellow Wood Flooring


Trigger Font Gun barrel Air gun Rectangle


Liquid Automotive lighting Amber Automotive parking light Yellow
 
421 - 440 of 455 Posts
Top