Joined
·
13,854 Posts
Posts by racer88
1 - 20 of 193 Posts
Joined
·
13,854 Posts
Have you thought about which model you'd like to build?
This one will be a G34.
You might consider buying a P80 frame sooner rather than later. A lot of online retailers are having good sales right now. I'm wondering if there's a reason they're dumping inventory. Hmmmmm.
Joined
·
13,854 Posts
It was a similar decision when my Subaru STI engine "done blowed up."
Rebuild it back to factory spec?
Aw, hellz no! Build it BETTER! Stronger. Faster.
If I'm going to build a gun, I'm going to BUILD a GUN!
Joined
·
13,854 Posts
Well, no... it's not finished. I've got the tabs off. I've drilled the holes. Next is the channel. I should have it close to finished, if not finished over this long weekend.Yet, you still haven’t built it.
Sent from my iPhone using Tapatalk
Joined
·
13,854 Posts
Which website? There are tons of sales going on now for P80 frames. Many in the $99 range.
Joined
·
13,854 Posts
PF45 80% Pistol Frame: BLACK
WE DO NOT SHIP POLYMER80 FRAMES TO: Hawaii, New Jersey, New York, & Washington. ORDERS WILL BE CANCELED AND CHARGED A 20% CANCELLATION FEE.
www.durkintactical.com
Polymer80 PF45 80% Frame for GLOCK 20/21 | granger-tactical
F45™ Large FrameThe industry’s only 80% Large Polymer Pistol Frame offers our enhanced ergonomics and features. Built with high-strength reinforced polymer construction, the PF45™ compatible with Glock® G21SF components. It is available with our aggressive standard grip texture which also allows...
www.grangertactical.com
Joined
·
13,854 Posts
Yeah... Polymer80.com is out of everything. But there are TONS of frames available at good prices all over the place. $99 - $110 range.
Joined
·
13,854 Posts
Tonight I carved out the recoil spring channel. The whole time I was laughing at the BULL**** spewed by Biden saying, "All you have to do is get a kit, and in half an hour, you've got a gun!" LOLOLOLOL!
I spent at least a few hours JUST on the channel.
I spent at least a few hours JUST on the channel.
Joined
·
13,854 Posts
I shall now bear my Dremeling soul.
One comment... the aftermarket flex-shaft... it's a POS. The run-out is horrible. Any diamond or other rotary instrument I put in there wobbles like crazy when I turn on the Dremel. Directly in the Dremel... no wobble. The collet / chuck is not concentric. At all. It's quite horrible. To the point of unusable.
Some photos. I ended up with a gouge - letting the green point dwell on one point for too long. Tried to polish it out as best I could.
I used the Ergo Mast to hold the frame so I could use both hands to steady the Dremel.
![72106]()
![72107]()
![72108]()
One comment... the aftermarket flex-shaft... it's a POS. The run-out is horrible. Any diamond or other rotary instrument I put in there wobbles like crazy when I turn on the Dremel. Directly in the Dremel... no wobble. The collet / chuck is not concentric. At all. It's quite horrible. To the point of unusable.
Some photos. I ended up with a gouge - letting the green point dwell on one point for too long. Tried to polish it out as best I could.
I used the Ergo Mast to hold the frame so I could use both hands to steady the Dremel.
Joined
·
13,854 Posts
Ah... the word on the street is that the P45 parts are scarce right now. So, you may be able to get a frame now. But, parts may be slow coming.
1 - 20 of 193 Posts
Join the discussion
